Page 234 - Mechanical Products Installation Handbook IH-1000M

226 MECHANICAL TEES & CROSSES Figure 730 Grooved Tees and Crosses
(1 of 2)
BC A
E
O.D. Inches mm
4.500 x 1.315
114,3 x 33,4
4.500 x 1.900
114,3 x 48,3
4.500 x 2.875
114,3 x 73,0
4.500 x 3.500
114,3 x 88,9
5.563 x 2.375
141,3 x 60,3
—
139,7 x 76,1
—
139,7 x 48,3
—
139,7 x 73,0
FIGURE 730 MECHANICAL TEE GROOVED OUTLET
Nominal Run x Branch ANSI Inches DN
4 x1
100 x 25
4 x 1-1/2
100 x 40
4 x 2-1/2
100 x 65
4 x3
100 x 80
5 x2
125 x 50
5 x 76,1mm
125 x 65
139,7mm x 1-1/2
125 x 40
139,7mm x 2-1/2
125 x 65
Nominal Dimensions - Inches / mm
A
B
C
E
3.69
7.13
3.07 2.78
78,0 70,6
3.56 2.78
90,4 70,6
4.38 2.78
111,3 70,6
5.13 2.78
130,3 70,6
4.06 3.37
103,1 85,6
4.38 3.37
111,3 85,6
3.56 3.37
90,4 85,6
4.38 3.37
111,3 85,6
93,7 181,1
4.00 7.13
101,6 181,1
4.00 7.13
101,6 181,1
4.13 7.13
104,9 181,1
4.63 8.13
117,6 206,5
4.75 8.13
120,7 206,5
4.63 8.13
117,6 206,5
4.75 8.13
120,7 206,5
4 x 1-1/4
100 x 32
4.500 x 1.660
114,3 x 42,2
3.92
99,6
7.13
181,1
3.32
84,3
2.78
70,6
4 x2
100 xN50
4.500 x 2.375
114,3 x 60,3
4.00
101,6
7.13
181,1
4.06
103,1
2.78
70,6
4 x 76,1mm
100 x 65
—
114,3 x 76,1
4.00
101,6
7.13
181,1
4.38
111,3
2.78
70,6
5 x 1-1/2
125 x 40
5.563 x 1.900
141,3 x 48,3
4.63
117,6
8.13
206,5
3.56
90,4
3.37
85,6
5 x 2-1/2
125 x 65
5.563 x 2.875
141,3 x 73,0
4.75
120,7
8.13
206,5
4.38
111,3
3.37
85,6
5 x3
125 x 80
5.563 x 3.500
141,3 x 88,9
5.00
127,0
8.13
206,5
5.13
130,3
3.37
85,6
139,7mm x 2
125 x 50
—
139,7 x 60,3
4.63
117,6
8.13
206,5
4.06
103,1
3.37
85,6
a. Proper outlet hole preparation is required for effective sealing and performance. Inspect the pipe seal surface within 5/8” (15,9 mm) of the hole to ensure it is free from conditions that would adverse- ly affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area that might affect assembly, proper seating of the locating collar or flow from the outlet. For Mechanical Crosses, ensure double outlet holes are aligned on opposite sides of the pipe.