Page 232 - Mechanical Products Installation Handbook IH-1000M

224 MECHANICAL TEES & CROSSES Figure 730 Grooved Tees and Crosses
(1 of 2)
BC A
E
O.D. Inches mm
2.375 x 1.660
60,3 x 42,2
2.875 x 1.315
73,0 x 33,4
2.875 x 1.900
73,0 x 48,3
—
76,1 x 33,4
—
76,1 x 48,3
3.500 x 1.315
88,9 x 33,4
3.500 x 1.900
88,9 x 48,3
FIGURE 730 MECHANICAL TEE GROOVED OUTLET
Nominal Run x Branch ANSI Inches DN
2 x 1-1/4
50 x 32
2-1/2 x 1
65 x 25
2-1/2 x 1-1/2
65 x 40
76,1mm x 1
65 x 25
76,1mm x 1-1/2
65 x 40
3 x 1
80 x 25
3 x 1-1/2
80 x 40
Nominal Dimensions - Inches / mm
2.78 4.88 3.32 1.59
70,6 124,0 84,3 40,4
2.88 5.25 3.07 1.81
73,2 133,4 78,0 46,0
3.07 5.25 3.59 1.81
78,0 133,4 91,2 46,0
2.94 5.62 3.07 1.87
74,5 142,7 78,0 47,5
3.13 5.62 3.56 1.87
79,5 142,7 90,4 47,5
3.19 6.13 3.07 2.21
81,0 155,7 78,0 56,1
3.38 6.13 3.56 2.21
85,9 155,7 90,4 56,1
A
B
C
E
2x1
50 x 25
2.375 x 1.315
60,3 x 33,4
2.62
66,5
4.88
124,0
3.07
78,0
1.59
40,4
2 x 1-1/2
50 x 40
2.375 x 1.900
60,3 x 48,3
2.62
66,5
4.88
124,0
3.32
84,3
1.59
40,4
2-1/2 x 1-1/4
65 x 32
2.875 x 1.660
73,0 x 42,2
3.00
76,2
5.25
133,4
3.56
90,4
1.81
46,0
2-1/2 x 2
65 x 50
2.875 x 2.375
73,0 x 60,3
3.19
81,0
5.25
133,4
4.00
101,6
1.81
46,0
76,1mm x 1-1/4
65 x 32
—
76,1 x 42,2
3.06
77,7
5.62
142,7
3.56
90,4
1.87
47,5
76,1mm x 2
65 x 50
—
76,1 x 60,3
3.25
82,6
5.62
142,7
4.00
101,6
1.87
47,5
3 x 1-1/4
80 x 32
3.500 x 1.660
88,9 x 42,2
3.34
84,8
6.13
155,7
3.32
84,3
2.21
56,1
3 x2
80 x 50
3.500 x 2.375
88,9 x 60,3
3.50
88,9
6.13
155,7
4.09
103,9
2.21
56,1
a. Proper outlet hole preparation is required for effective sealing and performance. Inspect the pipe seal surface within 5/8” (15,9 mm) of the hole to ensure it is free from conditions that would adverse- ly affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area that might affect assembly, proper seating of the locating collar or flow from the outlet. For Mechanical Crosses, ensure double outlet holes are aligned on opposite sides of the pipe.