Page 226 - Mechanical Products Installation Handbook IH-1000M

218 MECHANICAL TEES & CROSSES Figure 730 Threaded Tees and Crosses
(1 of 2)
DBC A
FIGURE 730 MECHANICAL TEE THREADED OUTLET
Nominal Run x Branch ANSI Inches DN
4 x 3
100 x 80
5 x 2
125 x 50
5 x 76,1mm
125 x 65
139,7mm x 1-1/2
125 x 40
139,7mm x 2-1/2
125 x 65
139,7mm x 3
125 x 80
6 x 1-1/2
150 x 40
E
O.D. Inches mm
4.500 x 3.500
114,3 x 88,9
5.563 x 2.375
141,3 x 60,3
—
139,7 x 76,1
—
139,7 x 48,3
—
139,7 x 73,0
—
139,7 x 3.500
6.625 x 1.900
168,3 x 48,3
Nominal Dimensions - Inches / mm
A
B
C
D Takeout
E
4 x 76,1mm
100 x 65
–
114,3 x 76,1
4.00
101,6
7.13
181,1
4.38
111,3
3.12
79,2
2.78
70,6
4.13 7.13
5.13
3.31 2.78
84,1 70,6
3.88 3.37
98,6 85,6
3.88 3.37
98,6 85,6
4.00 3.37
101,6 85,6
3.88 3.37
98,6 85,6
4.06 3.37
103,1 85,6
4.04 3.90
102,6 99,1
104,9 181,1 130,3
5 x 1-1/2
125 x 40
5.563 x 1.900
141,3 x 48,3
4.63
117,6
8.13
206,5
3.56
90,4
4.00
101,6
3.37
85,6
4.63 8.13
117,6 206,5
4.75 8.13
120,7 206,5
4.63 8.13
117,6 206,5
4.75 8.13
120,7 206,5
5.00 8.13
127,0 206,5
5.13 9.25
130,3 235,0
4.06
103,1
4.38
111,3
3.56
90,4
4.38
111,3
5.13
130,3
3.56
90,4
5 x 2-1/2
125 x 65
5.563 x 2.875
141,3 x 73,0
4.75
120,7
8.13
206,5
4.38
111,3
3.88
98,6
3.37
85,6
5 x3
125 x 80
5.563 x 3.500
141,3 x 88,9
5.00
127,0
8.13
206,5
5.13
130,3
4.06
103,1
3.37
85,6
139,7mm x 2
125 x 50
—
139,7 x 60,3
4.63
117,6
8.13
206,5
4.06
103,1
3.88
98,6
3.37
85,6
139,7mm x 76,1mm
125 x 65
—
139,7 x 76,1
4.75
120,7
8.13
206,5
4.38
111,3
3.88
98,6
3.37
85,6
6 x 1-1/4
150 x 32
6.625 x 1.660
168,3 x 42,2
5.13
130,3
9.25
235,0
3.56
90,4
4.25
108,0
3.90
99,1
6 x2
150 x 50
6.625 x 2.375
168,3 x 60,3
5.13
130,3
9.25
235,0
4.06
103,1
4.31 109,5
3.90 99,1
a. Proper outlet hole preparation is required for effective sealing and performance. Inspect the
pipe seal surface within 5/8” (15,9 mm) of the hole to ensure it is free from conditions that would adversely affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing contact area that might affect assembly, proper seating of the locating collar or flow from the outlet. For Mechanical Crosses, ensure double outlet holes are aligned on opposite sides of the pipe. The use of threaded components other than steel pipe, such as dry type sprinklers, etc. may not be compatible with the female threaded outlets of Mechanical Tees and Crosses. Always confirm compatibility by contacting your Tyco Mechanical Products representative.