Page 222 - Mechanical Products Installation Handbook IH-1000M

214 MECHANICAL TEES & CROSSES Figure 730 Threaded Tees and Crosses
(1 of 2)
DBC A
FIGURE 730 MECHANICAL TEE THREADED OUTLET
Nominal Run x Branch ANSI Inches DN
2 x 3/4
50 x 20
2 x 1-1/4
50 x 32
2-1/2 x 1/2
65 x 15
2-1/2 x 1
65 x 25
2-1/2 x 1-1/2
65 x 40
76,1mm x 1/2
65 x 15
76,1mm x 1
65 x 25
E
O.D. Inches mm
Nominal Dimensions - Inches (mm)
2.62 4.88 3.07 2.12 1.59
66,5 124,0 78,0 53,8 40,4
2.78 4.88 3.32 1.93 1.59
70,6 124,0 84,3 49,0 40,4
2.88 5.25 3.07 2.38 1.81
73,2 133,4 78,0 60,5 46,0
2.88 5.25 3.07 2.38 1.81
73,2 133,4 78,0 60,5 46,0
3.07 5.25 3.59 2.17 1.81
78,0 133,4 91,2 55,1 46,0
2.94 5.62 3.07 2.44 1.87
74,5 142,7 78,0 62,0 47,5
2.94 5.62 3.07 2.44 1.87
74,5 142,7 78,0 62,0 47,5
A
B
C
D Takeout
E
2 x 1/2
50 x 15
2.375 x 0.840
60,3 x 21,3
2.62
66,5
4.88
124,0
3.07
78,0
2.12
53,8
1.59
40,4
2.375 x 1.050
60,3 x 26,7
2.375 x 1.660
60,3 x 42,2
2.875 x 0.840
73,0 x 21,3
2.875 x 1.315
73,0 x 33,4
2.875 x 1.900
73,0 x 48,3
—
76,1 x 21,3
—
76,1 x 33,4
2 x1
50 x 25
2.375 x 1.315
60,3 x 33,4
2.62
66,5
4.88
124,0
3.07
78,0
2.12
53,8
1.59
40,4
2 x 1-1/2
50 x 40
2.375 x 1.900
60,3 x 48,3
2.75
69,9
4.88
124,0
3.32
84,3
1.93
49,0
1.59
40,4
2-1/2 x 3/4
65 x 20
2.875 x 0.840
73,0 x 21,3
2.88
73,2
5.25
133,4
3.07
78,0
2.38
60,5
1.81
46,0
2-1/2 x 1-1/4
65 x 32
2.875 x 1.660
73,0 x 42,2
3.00
76,2
5.25
133,4
3.56
90,4
2.19
55,6
1.81
46,0
2-1/2 x 2
65 x 50
2.875 x 2.375
73,0 x 60,3
3.19
81,0
5.25
133,4
4.00
101,6
2.44
62,0
1.81
46,0
76,1mm x 3/4
65 x 20
—
76,1 x 26,7
2.94
74,5
5.62
142,7
3.07
78,0
2.44
62,0
1.87
47,5
76,1mm x 1-1/4
65 x 32
—
76,1 x 42,2
3.06
77,7
5.62
142,7
3.56
90,4
2.25
57,2
1.87
47,5
a. Proper outlet hole preparation is required for effective sealing and performance. Inspect the pipe seal surface within 5/8” (15,9 mm) of the hole to ensure it is free from conditions that would adversely affect proper gasket sealing. Remove any sharp or rough edges from the hole or upper housing con- tact area that might affect assembly, proper seating of the locating collar or flow from the outlet. For Mechanical Crosses, ensure double outlet holes are aligned on opposite sides of the pipe. The use of threaded components other than steel pipe, such as dry type sprinklers, etc. may not be compat- ible with the female threaded outlets of Mechanical Tees and Crosses. Always confirm compatibility by contacting your Tyco Mechanical Products representative.