Page 113 - GRINNELL Mechanical Grooved Piping Products EMEA

Preparation Equipment
Roll Groove Standard Specification for Steel & Other IPS Pipe
Tech Data Sheet: G710
B A
C
D
0.062 0.062 0.062 0.078 0.076 0.078 0.083 0.083 0.083 0.083 0.084 0.083 0.085
(Page 1 of 2)
T
OD
GRINNELL Roll Grooves conform to AWWA C-606 specification.
Nominal Pipe Size mm Inches
Pipe O.D. mm Inches
A ±0,76mm ±0.030" mm Inches
B ±0,76mm ±0.030" mm Inches
C
Groove Diameter mm Inches
D Groove Depth (ref. only) mm Inches
T Minimum Wall mm Inches
Maximum Allow Flare Diameter mm Inches
O.D.
Tolerance
+
-
Actual
Tol. +0.000
32
42.4
0.41
0.41
15.88
7.14
38.99
-0.38
1.60
1.65
44.96
11⁄4 1.660 11⁄2 1.900 2 2.375 21⁄2 2.875 76.1mm 3.000 3 3.500 108.0mm 4.252 4 4.500 133.0mm 5.236 139.7mm 5.500 5 5.563 159.0mm 6.260 165.1mm 6.500
0.016 0.016 0.625 0.019 0.019 0.625 0.024 0.024 0.625
0.029 0.029 0.625
0.030 0.030 0.625
0.035 0.031 0.625 0.043 0.031 0.625 0.045 0.031 0.625 0.053 0.031 0.625 0.056 0.031 0.625 0.056 0.031 0.625 0.063 0.031 0.625 0.063 0.031 0.625
0.281 1.535 -0.015 0.281 1.775 -0.015 0.344 2.250 -0.015 0.344 2.720 -0.018 0.344 2.845 -0.018 0.344 3.344 -0.018 0.344 4.084 -0.020 0.344 4.334 -0.020 0.344 5.084 -0.022 0.344 5.334 -0.022 0.344 5.395 -0.022 0.344 6.084 -0.030 0.344 6.330 -0.022
0.065 0.065 0.065 0.083 0.083 0.083 0.083 0.083 0.109 0.109 0.109 0.109 0.109
1.77 2.01 2.48 2.98 3.10 3.60 4.35 4.60 5.35 5.60 5.66 6.35 6.60
40
48.3
0.48
0.48
15.88
7.14
45.09
-0.38
1.60
1.65
51.05
50
60.3
0.61
0.61
15.88
8.74
57.15
-0.38
1.60
1.65
62.99
65
73.0
0.74
0.74
15.88
8.74
69.09
-0.46
1.98
2.11
75.69
65
76.1
0.76
0.76
15.88
8.74
72.26
-0.46
1.93
2.11
78.74
80
88.9
0.89
0.79
15.88
8.74
84.94
-0.46
1.98
2.11
91.44
100
108.0
1.09
0.79
15.88
8.74
103.73
-0.51
2.11
2.11
110.49
100
114.3
1.14
0.79
15.88
8.74
110.08
-0.51
2.11
2.11
116.84
125
133.0
1.35
0.79
15.88
8.74
129.13
-0.56
2.11
2.77
135.89
125
139.7
1.42
0.79
15.88
8.74
135.48
-0.56
2.11
2.77
142.24
125
141.3
1.42
0.79
15.88
8.74
137.03
-0.56
2.13
2.77
143.76
150
159.0
1.60
0.79
15.88
8.74
154.53
-0.76
2.11
2.77
161.29
150
165.1
1.60
0.79
15.88
8.74
160.78
-0.56
2.16
2.77
167.64
(1) The maximum allowable tolerances for IPS Pipe from square cut ends is:
0.76mm (0.030") for sizes 32mm – 80mm
(11⁄4" thru 3");
1.14mm (0.045") for sizes 100mm – 150mm
(4" – 6"); and
1.52mm (0.060") for sizes 200mm (8") and above.
(2) Gasket Seating Surface “A” must be free from score marks, ridges, indentations, projections, loose paint, scale, dirt chips, grease, rust, etc. that would prevent a positive seal.
(3) Groove Diameter “C” must be of uniform depth around the circumference of the pipe.
(4) Groove Depth “D” is a reference dimension only. The Groove Diameter “C” must be maintained.
(5) Minimum Wall Thickness “T” is the minimum wall thickness that should be roll grooved.
(6) Maximum allowable pipe end flare diameter is measured at the pipe end diameter.
Caution: Pressure performance values shown for GRINNELL couplings on light wall (Sch. 5 & Sch. 10 ISO Metric) stainless steel pipe are dependent on the use of required special rolls for roll grooving light-wall stainless steel pipe. Failure to utilize the required special rolls for roll grooving light-wall stainless steel pipe may result in equipment failure.
113